Setup NAS Server on Raspberry Pi 3

NAS servers are really costly these days. If you don’t have that much money to spare, then you use Raspberry Pi 3 to set up a low cost NAS server very easily. In this article, I will show you how to set up a low cost NAS server using a Raspberry Pi 3. I will use Raspberry Pi 3 Model B for the demonstration in this article. But any model of Raspberry Pi 3 should work just fine. So, let’s get started.

To build a low cost NAS server with Raspberry Pi 3, all you need is:

A USB hard drive dock and a SATA 2.5” or 3.5” hard drive. You can also use a USB thumb drive for storage. It’s up to you.
A Raspberry Pi 3 Model B or Raspberry Pi 3 Model B+.
A microSD card with Raspbian OS flashed. I have a dedicated article on installing Raspbian on Raspberry Pi. You can check it out at LinuxHint.com.
An Ethernet cable.
An Android Phone charger for powering up Raspberry Pi 3.

Connecting to Raspberry Pi Remotely:

Now, connect all the required components such as USB thumb drive or USB self-powered hard drive (using a USB hard drive dock), microSD card with Raspbian OS image flashed, Ethernet cable, and micro USB power cable. Finally, power on your Raspberry Pi. Now, connect to your Raspberry Pi via SSH or VNC depending on your preference.

NOTE: Use the username pi and the password that you set while configuring Raspbian for the first time. If you’ve configured Raspberry Pi headless, then the default password is raspberry.

To connect to your Raspberry Pi via SSH, use GitBash or PuTTY. Both of them are free to download and use. To connect to your Raspberry Pi via VNC, use VNC Viewer from RealVNC. It is free to download and use. Once you’re connected, you are ready to move on to the next section.

Installing Samba on Raspberry Pi:

In this article, I will use Samba on Raspberry Pi for file sharing. It allows file sharing using Windows SMB or CIFS protocol. Windows has native support for Samba shares. Samba is available in the official package repository of Raspberry Pi. So, it is very easy to use. First, open up a Terminal and update the APT package repository cache with the following command:

$ sudo apt update

Now, install Samba with the following command:

$ sudo apt install samba

Now, press y and then press <Enter> to continue.

Samba should be installed.

Mounting Storage Devices:

Now that Samba is installed, it’s time to mount the USB thumb drive or USB hard drive on your Raspberry Pi. First, connect your USB thumb drive or USB hard drive on Raspberry Pi.

Usually, it will be available in /dev/sda1.

If you’re unsure, you can find out what it is for you with the following command:

$ lsblk

As you can see, the block device is sda and the partition is sda1 in my case. So, the partition can be accessed as /dev/sda1.

Now, create a directory (let’s call it Media) where you want to mount the USB thumb drive or hard drive with the following command:

$ sudo mkdir /mnt/Media

Now, edit /etc/fstab file with the following command:

$ sudo nano /etc/fstab

Now add the line as marked in the screenshot below at the end of the /etc/fstab file. Once you’re done, save the file with <Ctrl> + x and then press y followed by <Enter>.

NOTE: Here, ext4 is the filesystem format of the USB thumb drive or hard drive you want to mount. It may be different for you. Make sure you put the right filesystem type here.

Now, mount the partition /dev/sda1 to /mnt/Media mount point with the following command:

$ sudo mount /mnt/Media

Your USB thumb drive or hard drive should be mounted in the /mnt/Media mount point as you can see in the screenshot below.

$ df -h

Now, change the owner of the /mnt/Media mount point to pi with the following command:

$ sudo chown -Rf pi:pi /mnt/Media

Configuring Samba Share:

Now, edit the Samba configuration file /etc/samba/smb.conf with the following command:

$ sudo nano /etc/sambab/smb.conf

The /etc/samba/smb.conf configuration file should be opened. Now, at the end of the configuration file, type in the lines as marked in the screenshot below. Once, you’re done, save the file.

Now, run the following command to make your existing pi user a Samba user and set a password for the Samba user:

$ sudo smbpasswd -a pi

Now, type in a Samba password and press <Enter>.

Retype the same password and press <Enter>.

A Samba user pi should be added.

Finally, restart your Raspberry Pi with the following command:

$ sudo reboot

Connecting to the Raspberry Pi NAS Server:

Now that you’ve successfully configure the Raspberry Pi NAS server, you can connect to it from your Windows computer and any other devices that has support for SMB/CIFS protocol. First, check the IP address of your NAS server. It is the same as the IP address of your Raspberry Pi. If you remember it, skip to the next instruction.

$ ip a